五金钮用英语怎么说

供稿:hz-xin.com     日期:2022-06-10
hardware button 五金纽扣

双面撞钉用英语翻译是:Double side impact nail,见下图翻译



胸 围
腰 围
臀 围
前 胸 宽
背 宽
肩 宽
后颈点至腰
颈肩点至腰
颈 围
下 臂 长
臂 围
裙 长
内侧裤长
Bust
Waist
Hips
Front Width
Back Width
Shoulder
C.B.N-Waist
N.S.P-Waist
Neck
Sleeve Underarm
Sleeve Muscle
Long Skirt
Inside Trouser Leg.
由肩点量袖长
(总袖长)
背 长
前 身 长
背 宽
肘 长
开 裆 处
颈 点 至 腰
身 长
实 际 腰 围
腰 带
裤 长
(不算腰带宽)
Over Shoulder Sleeve Measure
Length of Back
Length of Front
Breadth of Back
Elbow
Rise
Neck to Waist
Height
Nat Waist
Waist Band
Trousers Side- seam Without Band
Ⅲ. 制衣专有名词:
Jersey wear 针
Woven 梭织
Knitwear/Sweater 毛衫
Accessory 配件
Solid 净色
Print 印花
Embroidery 绣花
Beading 钉珠
M/C Embroidery 机绣
Hand crochet 手钩
Embellishment 装饰类
Princess line 公主线
Outseam, inseam. 外骨, 里骨.
Grain line 布纹
Straight grain 直纹
Cross grain 横纹
Bias cutting 斜纹裁
Shiny 反光
Twist 扭曲
Hiking 吊起
Tight 紧的
Loose 松的
Stretched 拉松
Puckering 容邹
Unbalance 不平衡
Check match 对格
Stripe match 对条
Vertical buttonhole 直钮门
Horizontal buttonhole 横钮门
Seam allowance 子口
Interlining 朴
Elastic 丈巾
Main label 主唛
Content label 身分唛
Care label 洗水麦
Thread 线
Zipper 拉链
Spare button 士啤钮
Interface 内贴
Lining 里布
Shoulder pad 肩垫
Tissue paper 拷贝纸
Price ticket 价钱牌
Hangtag 挂牌
Poly bag 胶袋
Hanger 衣架
Inner box 内箱
Carton 纸箱
Dye to match=D.T.M配色
Double turn 还口
Fabric defects 布疵
Rough yarn 粗纱
Color yarn 色纱
Buying/Photo shoot/Fitting/Grades/Gold seals/Mock shop
销售/影像/尺寸/齐码尺寸/落货前/展览 办
Pilot/Wearer trial 头版/试穿办
CAD System
Four points system
Pre-shrinkage m/c
Fabric hanger
Color continuity card
Fusing m/c
Thermal paper
Workshop
Pre-production meeting
Straight-line production
Lockstitch-Single/Twin needle
Overlock-----3/4/5 thread
Twin ndl seam cover----flat bed/ Cylinder arm
4 ndl flat lock 哈须
Bar Tack
Button sew----lockstitch /Chainstitch
Botton hole-----lockstitch/Key hole
Zig zag
Blind hem
M/c maintenance/service---------mechanic
Hand steam iron with vacuum
Spot cleaning
Metal detector
Ⅳ. 各部份疵点总汇
Collar 领
常见领形
Crew neck 圆领 Notch collar 国民领
V-neck v领 Shawl collar 菜瓜领
Boat Neck 船形领 Turtle neck 高翻领
U-neck u领 Sailor Collar 水手领
Square neck 方领 Peter-Pan collar 小飞侠领
Draped cowl 挂帽领 Chinese Collar 旗袍领
Wing collar 翼 领 Shirt collar 衬衫领
Italian Roll 意大利卷型领 V-with collar v翻领
领位评语
Unbalance collar 领不平衡
Asymmetric collar 领位差池称
Uneven collar width 左右领阔纷歧致
Uneven neckline 左右领圈纷歧致
Uneven collar point 领尖差池称
Uneven lapel shapes 左右前领咀形状纷歧样
Too much easing at C.F. neckline 前领口溶位太多(有太多溶位於前中领窝)
Collar too tight at CB 后领中太紧
Collar band is twisting 领座扭曲不平顺
Fullness at front collar and lapel 领及前领咀不平顺
Neckline is not smooth 领圈不圆顺
Neck setting not smooth 领子装得不平顺
High & low back neck 后领圈有崎岖
Edge of front opening is crooked 前门领边不直
Front opening not straight 前门领边不直
Front facing is exposed at bottom hem 前门领贴在下摆处外露
Front opening facing is shorter than body 前门领贴短於大身
Neck was stretched 领圈拉松
Too much tie on front collar 前领处有豁口
Sleeve & Armhole 袖&夹
Puckering at left/right armhole 左右夹圈有溶位不平伏.
Too loose at right armhole, uneven for left/right armhole 右夹圈有拉松, 左右夹圈不相称.
Sleeve running to back(衣袖走后) / Sleeve running to front(衣袖走前) 操兵袖
Too loose at front sleeve seam 前袖骨拉松
Too tight at back sleeve seam 后袖骨过紧.
Poor cuff setting 卡夫装得欠好
Sleeve placket is not set well 袖叉装得欠好
Underarm seam was stretched 袖底缝被拉松
Armhole setting not smooth 袖孔不圆顺
Ease on sleeve cap is uneven 袖顶缩拱不均匀
Front/back 前后幅
Hiking at front, CF facing too short 吊襟
Hiking at back, lining too short 吊里
Curve at CF zip(too much fullness at CF zip) 前中拉链溶位太多
Curve at CF zipper because of no easing of zipper. 前中拉链无溶位(引致纽曲)
Hiking at back / Hiking at front 后幅吊起 / 前幅吊起
Front panel is bigger than under panel(lining) 前幅底幅细面幅松
Lining too big, too short, too small, too long 里布太大, 太短, 太小, 太长
Grain lines are not match at front & back panel 前后幅布纹不相称
Front length uneven 左右前长纷歧致
Too loose at shell, Too loose at back/lining, turn insider out 底松, 面松, 向外反
Hem 衫脚
Seam binding stitch tension is too tight, causing bottom not smooth. 下摆丝带过紧, 使下摆不平顺
Bottom hem is not in line / not straight. 下脚不够不平(直)
Twisting hem, puckering at hem 下脚纽纹起豆角.
Uneven hem 左右下摆崎岖纷歧
Vent length uneven 左右开叉是非纷歧
Uneven leg length 是非脚
Uneven hem line 衫脚不平均 / 差池称
Pocket 袋
High-low pocket 崎岖袋
Both pocket set uneven 左右口袋装得崎岖纷歧
Pocket not smooth / squared 袋不平服/不够正方
Pocket flap not centered over pocket 袋盖不正中
Both pocket shapes are uneven 左右口袋形状纷歧致
Bottom part of pocket is sagging 口袋下部下垂
Pocket flap is misplaced 袋边位置差池
Pocket is misplaced 口袋位置差池
Pocket is smiling 袋口开得不吻合
Pocket opening is fray 袋口有毛口
Pocket shape distorted 口袋变形
Pocket size and shape is not follow sample exactly 口袋的尺寸及形状未凭据实样做
Pocket welt is uneven 上下袋唇不均匀
Poor pocket setting 口袋装得欠好
Binding 拉捆
Piping is uneven 捆边不均匀
Piping is twisting and not smooth 捆边扭曲不平顺
Pleats 缩褶
Uneven shirring at back waist seam
后腰缩碎褶不均匀。
Shirring 碎褶
Elastic shirring is uneven 橡筋缩拱不均匀
Both side pleats not balance 左右褶位纷歧致
Darts placement is not follow sample exactly 褶位未凭据实样做
Pleats is misplaced 褶位差池
Shirring / Gathering 缩褶
Pleated 生褶
Darts 死褶
Beading & embroidery 钉珠&绣花
Beads stitching are not secure 珠子未钉牢
Embroidery stitching is too tight 绣花线太紧
Embroidery stitching too loose 绣花线太松
SHADING DEFECTS 色差问题
1) Color shading 色差
2) Color shading within one garment. 同一件衣服内有色差。
3) Color shading between trims and body. 配件与衫身之间有色差。
4) Shade differs from approved standard. 颜色与批核色版差异。5) Shading caused by poor color interlining matching. 纸朴颜色不配合, 引致色差。
ACCESSORIES 辅料问题
1) Missing button / label / badge 漏钮 / 漏唛头 / 漏章
2) Button position not well match buttonhole. 钮与钮门位置欠配合
3) Button inside out 钮的底面倒置
4) Button marking not removed. 点钮笔痕没有清除
5) Damaged button/buttonhole 钮烂/烂钮门
6) Rusted stud 工字钮生锈
7) Paint peel off on stud 工字钮颜色脱落
8) Button and buttonhole not aligned cause bulge. 钮及钮门位置不配合, 引致谷起
9) Buttonhole too small to allow button to pass through. 钮门太细, 钮不能顺利通过
10) Uncut buttonhole / partially cut buttonhole 钮门未开 / 钮门未开尽
11) Ragged edges at buttonhole 钮门纱线不清
12) Broken buttonhole stitches 钮门断线
13) Button thread easily pulled out. 钉钮线容易拉脱
14) Snap / rivet easily pulled off.吸钮、撞钮容易拉脱
15) Buttonhole is not match button size 钮洞尺寸与钮扣巨细不相配
16) Button misplaced 钮扣位置差池
17) Buttonhole misplaced 钮洞位置差池
18) Button is not sewing security 钮扣未钉牢
19) Button is sewn too tight 钮扣钉得太紧
20) Buttonhole is fray 钮洞有毛口
21) Key buttonhole density is too loose 凤眼钮洞的车缝线步太疏
22) Key buttonhole is misplaced 凤眼钮洞位置差池
23) Snap misplaced 揿钮位置差池
24) Snap tape is misplaced 揿钮扁带位置差池
25) Snap tape setting not well 揿钮扁带装得欠好
26) There is bubble on buttonhole area 钮洞周围有气泡
27) Hood and bar is misplaced 裙扣位置差池
28) Hole at zip top / end 拉链顶 / 尾有洞
29) Zipper setting is twisting 拉链装得扭曲
30) Shoulder pad not attach to garment security 肩棉未钉牢
31) Shoulder pad not cover well 肩棉未包好
32) Velcro is misplaced 么术贴位置差池
33) Waistband belt is not set straight 腰耳装得不直
34) Waistband belt length and width are uneven 腰耳的长、宽纷歧致
35) Incomplete adhesive on interlining. 黏朴未完全黏好
36) Strike through of adhesive on interlining. 黏朴胶露面
37) Strike back of adhesive on interlining. 黏朴脱落
38) Blistering occurred on interlining. 黏朴起泡
39) Insecure shoulder pad attached. 肩棉钉缝不稳
40) Label placement incorrect. 唛头位置不正确
41) Care label content not as specified. 成份唛内容不切合要求
42) Main label and size/content label are set too closed 主唛与尺码成份唛装得太靠近
43) Main label setting is misplace 钉主唛不井齐
44) Wrong care label sewn on garment. 成份唛车错位置
(45) Label not properly secured. 唛头车缝不稳
(46) Label sewn beyond label edge. 唛头车缝太入
(47) Label sewing seam uneven / puckered. 唛头车缝不平均或起皱
48) Wrong accessories used. 用错辅料
STITCHING AND SEAMS 线步和骨位
1) Raw edge 散口
2) Raw edges 爆口
3) Untrimmed thread ends 线头未剪
4) Skipped stitches 跳线
5) Exposed stitching 露线
6) Broken stitches 断线
7) Run-off stitches 间线落坑
8) Crooked stitches 线步弯曲
9) Poor join stitching 驳线欠佳
10) Unsightly over-lapping stitches 驳线不良
11) Stitches too loose 线步太松
12) Stitches too tight 线步太紧
13) Distorted stitches 车线不直
15) Expose stitch 落坑线外露
16) Inconsistent stitching 线步纷歧致
17) Uneven width on double stitching 双线阔窄不均
18) Uneven stitching density / tension 线步密度 / 松紧度不平均
19) 1/4 top stitch not even 1/4面线有宽窄
20) Expose safety stitch 保险线外露
21) Inseam is uneven 内缝线不井齐
22) Merrow stitch density is too big 拨边线步太疏
23) Overlap stitch is not well 反缝的接线欠好
24) Top & under stitch tension not match 底面线力不相符
25) Uneven merrow seam 内拨边线弯曲不直
26) Missing reinforcement stitches 漏车加固线步
27) Row of stitching missing – top stitch 漏车一行线——平车线
28) Stitch count less than standard 线步较尺度少
29) All top stitch is uneven 所有的面线都不均匀
30) Blind stitch is broken 筒针有断线现象
31) Blind stitch is wavy 筒线弯曲不直
32) Shoulder seam not smooth 小肩缝弯曲不直
33) Uneven folded width at bottom sweep 1/2″hemming. 折车1/2″脚围阔窄
34) Blind stitching visible 挑脚线露面
35) Incomplete seam stitching 线步不到尾
36) Uneven for hem closure stitching, uneven stitch at hem 下脚车线不直
37) Exposed waistband running stitches 裙头/裤头见坑线
38) Not straight at front fly 裤钮牌车线不顺直
39) Not straight at back yoke 后担干车线不直, 纽曲
40) Skipping stitches, looping stitches 跳线, 车线太松起耳仔
41) Seam allowance, sewing thread too tight 子口补间线, 线太紧起豆角
42) Pleated seam 骨位打褶
43) Puckered seam 骨位起皱
44) Open seam 爆骨
45) Burst seam 爆骨
46) Under seam visible 底骨露面
47) Waviness on seams 骨位起海浪
48) Twisted seams / Seam rolling 扭骨
49) Twisting at side seam, Wavy at side seam 侧骨纽, 不顺直.
50) Seam closures uneven 骨位结尾不平均
51) Missing bar-tack 漏打枣
52) Seam not properly secured 骨位不牢固
53) Fullness on seams 骨位太谷, 不平伏
54) Seam not fully opened before stitching. 骨位未完全拨开间线
55) Cracked seam 骨位拉时有响声(引致断线)
56) Too loose at princess seam 前公主骨拉松起泡
57) Puckering at back princess seam 后公主骨溶位太多, 起皱/起豆角
58) Too tight or too loose at side seam. 侧骨车线太紧或太松
59) Too loose at CF / CB seam 前中/后中骨太松
60) Too loose at shoulder seam, unbalance of front & back panel at shoulder seam 肩骨拉松(要落定位)
61) Too flat at shoulder seam, too slant of shoulder seam 肩骨太平/太斜
Ⅴ. 种种款式常见疵点
JEANS 牛 仔 裤
1) Waistband is wavy and twisting 腰头有弯曲
2) High-low waistband ends 崎岖裤头
3) Waistband corners not folded in right shape 裤头角位形状没有翻好
4) Too loose at front rise / back rise 裤浪过松
5) Twist hem 裤筒纽纹
6) Twist leg 左右裤筒差池称
7) Uneven leg length 是非脚
8) Twisted legs / twisted seam at legs 扭脾 / 脾位扭骨
9) Missing bar-tack 漏打枣
10) Inclined belt loops 歪耳仔
11) Mismatched belt loop color 耳仔颜色差池
12) Pocket bag caught in tack 袋布被打枣车死
13) Bulged fly 钮牌谷起
14) Zip exposed when buttoned 扣钮后拉链外露
15) Rusted studs / rivets 工字钮 / 撞钉生锈
16) Fabric easily torn at snap position 吸钮位布料容易撕烂
17) Snap easily pulled off 吸钮容易松睥
18) Holes at hem after washing 洗水后脚位有洞
19) Uneven washing effect 洗水效果不均匀
20) Different lots of shade 缸色
SHIRT / BLOUSE 恤衫 / 衬衣
1) Mismatched stripe check / print over 1/8″ 差池条 / 差池格 / 差池印花凌驾1/8″
2) Pattern matching is not well 衣服上的间条或格子未对好
3) Asymmetric collar 领位差池称 / 不平均
4) Uneven collar point 领尖差池称
5) Under collar exposed on outside of top collar 领反光
6) Open seam at collar points 领尖爆口
7) Uneven sleeve length 是非袖
8) Foreign matter sewn inside the finished collar / yoke / cuff 外来物藏於后领 / 担干 / 介英
9) Broken collar / cuff and hem after washed 洗水后烂领 / 烂介英 / 烂脚
10) Puckering at armhole 夹圈起皱
11) High-low pockets 崎岖袋
12) Pocket not smooth / squared 袋不平服/不够正方
13) Pocket flap not centered over pocket 袋盖不正中
14) Flap points not fully turned out 袋盖尖未完全翻出
15) Dart ends not stitched to a fine point 腰褶车线头尾未有翻针
16) Uneven hem line 衫脚不平均 / 差池称
17) Button out of line 钮位不成直线
18) Yellowish interlining being see through 发黄朴布外透
WOVEN JACKET 梭 织 外 衣
1) Bubbles on collar 领面起泡
2) Uneven length of collar point 领尖是非纷歧
3) Collar point too blunt/not smooth 领尖太钝, 不平滑.
4) Collar spread too wide/narrow 领尖距太阔/太窄
5) Tie space too big. 呔位太大
6) Lopsided collar/overlapping collar 歪领/叠领
7) Hi-low collar point(button down) 崎岖领尖(领咀钮)
8) Crooked/twisted collar 领扭曲
9) Fullness of top collar 领面布浮
10) Yellowish collar surface 领面布黄
11) Some residues inside collar 领内藏杂物.
12) Uneven placket width 筒阔欠平均
13) Twisted / crooked placket 筒扭曲
14) Bubbles at placket 筒面起泡
15) Front placket not down to hem. 前筒不能到尾
16) Uneven fullness at armhole 夹圈底的布太多(不平均)
17) Wrong way insertion of zip 拉链插位偏向错误
18) Snap easily pulled off 吸钮容易松脱
19) Non-functional of buckle / snap / zipper 坏扣 / 钮 / 拉链
20) Fabric easily torn at snap position 吸钮位布料容易撕烂
21) Button backing lining(single layer) 钮托底朴(单块布)
22) Uneven or loose elastication on ribs 罗纹弹力松紧不均
23) Loosened quilting stitches 间棉线步太松
24) Puckered seam at hood facing. 帽面骨位起皱
Ⅵ. WASHING 洗 水
1) Different lots of shade 缸色 / 色差
2) Uneven washing effect 洗水效果不均匀
3) Streaky mark 洗水(条纹)痕
4) Crease mark 洗水摺(白)痕
5) Pilly / hairy on garment surface 洗水后外貌有毛粒或起毛
6) Broken collar / cuff and hem 烂领 / 介英 / 脚
7) Sandy on garment surface 衣服外貌有沙的感受
8) Rock / sand inside pockets 袋内有石 / 沙
9) Different washing effect 洗水效果差异
10) Mildew or heavily odor garment. 霉味或很重的味在衣服上
Ⅶ. PRESSING 熨 衣
1) Poor pressing 烫工差
2) Wrinkle 皱
3) Wet 湿气
4) GMT press too hard cause shiny mark 衣服烫过头以致起光迹
5) Elastic is not pre-shrinkage before setting 橡筋未烫缩水
6) Seam not fully pressed open 骨位没有完全熨开
7) Crease mark 摺痕印
8) Burn mark 烧焦印
9) Water spot 水黑点
10) Color stain 颜色黑点
11) Melt 熔化
12) Glazing / shinny pressed 起镜
13) Sheer / glossy 起镜面
14) Pleated press 熨褶痕
15) Zip / button mark made by improper pressing 熨工欠佳, 引致有拉链痕 / 钮痕
16) Poor pressing / fusing of interlining 烫朴/ 压朴效果不佳
Ⅷ. CLEANLINESS 清 洁
Found oil stain 有油污渍
Dirty mark 污渍
There is dirty mark on garment 衣服上有脏迹
Cleaning mark 枪水渍 / 打枪痕迹
Ⅸ. PACKAGING / PRESENTATION 包 装
1) Missing price ticket / hangtag / label 欠价钱牌 / 挂牌 / 唛头
2) Wrong placement of price ticket / hangtag / label 价钱牌 / 挂牌 / 唛头位置错误
3) Wrong size / color in assortment 尺码 / 颜色分配错误
4) Improper folding 摺法不正确
5) Dirty poly bag 胶袋污渍
6) Broken export carton 外箱烂
7) Carton over weight 外箱过重
8) Incorrect carton size 外箱尺寸不合规格

五金四合钮用英语怎么说 - ------ : 你好!五金四合钮Metal snap button

五金的英文是什么?首先要求不要用百度在线翻译,那个不尺度,写成老外的叫法, - ------ :[答案] 就是Hardware,外贸通行叫法. Hardware store 五金商店 Hardware fitting 五金配件 Hardware tools 五金工具

英语翻译五金配件 - ------ :[答案] hardware fittings

"五金"一词怎么翻译成英文? - ------ :[答案] hardware 例句: I bought a screwdriver from a hardware store. 消费者对五金配件的选购越来越注重美观.

五金英语铝合金框.压条.等一些关于窗户的用英文怎么说 - ------ :[答案] 这个网站能找到你要找的词汇吧应该? 建筑工程行业英语词汇 屋子,住宅 house Haus 室内装饰 interior Inneneinrichtung 家具 furniture M(o)bel 墙壁 wall Wand 窗户 window Fenster 门 door T(u)r 地板 floor Boden 天花板 ceiling Decke 窗帘 curtain ...

手袋五金D扣用英语怎么说 - ------ : 你好!手袋五金D扣 Handbag hardware D buckle 如有疑问,请追问.

请问这句英文翻译成中文是什么意思?这是专业术语是五金门锁Brass flush bolt ------ : 铜门栓

懂五金配件或者脚手架配件英文的资助一下.急!!!!! - ------ : 1. Three claws disc nut 2. Two claw discs nut 3.60 steel brace nut 4.32 nut Direct selling 5. U-shape board 6. Pedal 7. The ladder 8.

五金图纸里面的英文 看不懂 哪个妙手资助翻译下 急~~~~~~~~~~ - ------ : See note 参见注意事项 GENERAL TOLERANCES Extrusion UNI EN 755 Machining UNI EN 22768-mk 总体公差 挤出按UNI EN 755 尺度 加工按UNI EN 22768-mk Heat sink: unfinished 加热槽:未处置 Pins: electro tin plated 销:电镀锡 Modified ...